Kicker 2006 ZX200.4 Manuel du propriétaire télécharger pdf (Page 2)

Installation . . . as easy as 1, 2, 3

1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The amplifier’s

end-panel controls need to be accessible for adjustment. Make sure there are no items behind the area

where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for

the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four

holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.

2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire

to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and

corrosion-free solid-metal area of the vehicle's

chassis.

Use a twisted pair(s) of RCA (low-level)

interconnect cable to feed the audio signal to

the amplifier. If you are using only one pair of

RCA inputs, connect the RCA cable to the AMP

1 inputs. Push the fader button out, and all four

channels will work with a single pair of RCA

input cable. Push the fader button in, when

using two pairs of RCA input cables. Keep the

RCA cable away from factory wiring harnesses

and other power wiring. If you need to cross this

wiring, cross it at a 90 degree angle.

Only use speaker wire (high-level) inputs if

your source unit does not have RCA type outputs. If you are using only one pair of high-level inputs,

connect the speaker wire to the AMP 1 input. Push the fader button out, and all four channels will work

with a single high-level input cable. Push the fader button in, when using both sets of high-level inputs.

Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your

amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground

wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it.

See the chart below for power and ground wire size, and fusing recommendations.

3. Configuration The following diagrams show the most common configurations for your Kicker ZX

series amplifier.

Four Channel Operation (Stereo) These ZX amplifiers are capable of operating into a minimum

impedance of 2 ohms per channel in stereo operation. See Figure 2.

Bridged Operation (Mono) ZX.4 series amplifiers are capable of operating into a minimum

impedance of 4 ohms when in bridged operation. See Figure 3.

Stereo and Bridged Operation Simultaneously The ZX.4 series amplifiers are capable of operating

into a minimum impedance of 4 ohms bridged and 2 ohms per channel in stereo operation. See

Figure 4.

INSTALLATION

ZX.4AMPLIFIER

ZX200.4

FourChannelModel:

ZX.4SeriesAmplifier

Owner’sManual

Congratulations on your

KICKER purchase

Please record your purchase

information and keep your sales

receipt for validation of warranty.

Authorized Kicker Dealer:

Purchase Date:

Amplifier Model Number:

Amplifier Serial Number:

__________________________

killers trk7“on Top”

RCA

INPUTS

BASSGAINGAINBASS

HI-LEVEL

INPUT

+ - - +

HI-LEVEL

INPUT

+ - - +

AMP 1 AMP 2

OFF HI LO

XOVER

OFF HI LO

XOVER

FADER

ON OFF

ModelZX200.4 Fuse30A PowerGroundWire 8GA

Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.

Battery

+12V

Fuse

Right Speaker AMP 2

Left Speaker AMP 2

18"

Or Less

(45cm)

Signal In AMP 1

Minimum impedance of 2 ohms per channel in stereo operation

Signal In AMP 2

Right Speaker AMP 1

Left Speaker AMP 1

24"

Or Less

(60cm)

Ground

Remote

Turn-On

Battery

+12V

Fuse

18"

Or Less

(45cm)

Signal In AMP 1

Minimum impedance of 4 ohms when in bridged operation

Signal In AMP 2

Mono Speaker AMP 1

Mono Speaker AMP 2

24"

Or Less

(60cm)

Ground

Remote

Turn-On

Battery

+12V

Fuse

18"

Or Less

(45cm)

Signal In AMP 1

Minimum impedance of 4 ohms when in bridged operation

and 2 ohms per channel in stereo operation

Signal In AMP 2

Right Speaker AMP 1

Mono Speaker AMP 2

Left Speaker AMP 1

24"

Or Less

(60cm)

Ground

Remote

Turn-On

2 3

Figure 1

Figure 2

Figure 3

Figure 4

Use only one type of signal input to the amplifier,

either RCA Cable or Speaker Wire

RCA Cable

(Low-Level)

AMP 1

Speaker Wire

(High-Level

Output)

Speaker Wire

(High-Level Input)

AMP 1

Left +

Left -

Right -

Right +

CONFIGURATION

ZX200.4

Speaker Wire

(High-Level Input)

AMP 2

Fader Button: Push in for

2 pairs of inputs, push out

for a single pair of inputs.

RCA Cable

(Low-Level)

AMP 2

Left +

Left -

Right -

Right +

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

Kicker 2006 ZX200.4 Manuel du propriétaire Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs audio pour voitures Kicker 2006 ZX200.4